Samsung nx 308 инструкция на русском

NX-SERIES Technical Manual NX-308 NX-820 NX-1232

PUBLICATION INFORMATION SAMSUNG ELECTRONICS Co. reserves the right to revise information in this publication for any reason without prior notice. SAMSUNG ELECTRONICS Co. also reserves the right to make changes in equipment design or components as engineering and manufacturing may warrant without

NX-SERIES NX-308 NX-820 NX-1232 ELECTRONIC KEY/HYBRID TELEPHONE SYSTEM TECHNICAL MANUAL INCLUDES : GENERAL DESCRIPTION SECTION INSTALLATION SECTION FEATURE SECTION PROGRAMMING SECTION APPENDIX SECTION BACK-UP DATA SHEETS

GENERAL DESCRIPTION SECTION

NX-SERIES HYBRID KEY SYSTEM GENERAL DESCRIPTION SECTION TABLE OF CONTENTS GENERAL DESCRIPTION NX-SERIES GENERAL SYSTEM DIAGRAM . . . . . . . . . . . . . . . . . 1-1 1. SYSTEM OVERVIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 1.1 NX-308 SYSTEM . . . . . . . . . . . . . . .

NX-SERIES HYBRID KEY SYSTEM GENERAL DESCRIPTION SECTION 5.3 ENVIRONMENTAL LIMITATIONS . . . . . . . . . . . . . . . . . . . . . . . 1-8 5.4 CABLE REQUIREMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8 5.5 SYSTEM TONES AND RINGS . . . . . . . . . . . . . . . . . . . . . . . . .

NX-SERIES HYBRID KEY SYSTEM GENERAL DESCRIPTION SECTION NX-SERIES GENERAL SYSTEM DIAGRAM 1-1

NX-SERIES HYBRID KEY SYSTEM GENERAL DESCRIPTION SECTION 1. SYSTEM OVERVIEW The NX-series hybrid key system accomodates three kinds of Key Station: NX-308, NX-820 and NX-1232. 1.1 NX-308 SYSTEM The NX-308, with a maximum capacity of three telephone C.O. lines and eight stations, is an analog

NX-SERIES HYBRID KEY SYSTEM GENERAL DESCRIPTION SECTION 2. NX-SERIES LAYOUT 2.1 TOP VIEW “POWER” LED “MONITOR” LED “IDLE” LCD 2.2 SIDE VIEW MDF Cable Path External Battery Connector Fuse Holder Power Switch Power Cable 1-3

NX-SERIES HYBRID KEY SYSTEM GENERAL DESCRIPTION SECTION 3. SYSTEM CONFIGURATION 3.1 NX-308 SYSTEM The basic KSU (Key Service Unit) comes equipped to operate three telephone lines and eight stations. Station #1 is assigned to be used with a keyset and stations #2 through #8 are assigned as keysets

NX-SERIES HYBRID KEY SYSTEM GENERAL DESCRIPTION SECTION 3.3 NX-1232 SYSTEM The basic KSU (Key Service Unit) comes equipped to operate eight telephone lines and sixteen stations. Stations #1 through #8 are assigned to be used with keysets or single line telephones, and stations #9 through #16 are

NX-SERIES HYBRID KEY SYSTEM GENERAL DESCRIPTION SECTION 4. HARDWARE DESCRIPTION 4.1 KSU (Key Service Unit) The KSU of the NX-series is a single cabinet, wall mounted, metal cased unit, containing the following: Power Supply Processing, switching, and customer memory for all ports. Internal music

NX-SERIES HYBRID KEY SYSTEM GENERAL DESCRIPTION SECTION 4.3 STATION EQUIPMENT Keyset with 24 buttons (NX-24E, NX-24B) Built-in speakerphone 24 programmable soft keys (12 with tri-colored LEDs) and 10 fixed-function keys UP/DOWN buttons for digital control of speaker, handset, and ringer volumes.

NX-SERIES HYBRID KEY SYSTEM GENERAL DESCRIPTION SECTION 5. SPECIFICATIONS 5.1 ELECTRICAL SPECIFICATIONS AC INPUT POWER CONSUMPTION MAX CURRENT DRAW AT 220 VAC RING GENERATOR BATTERY BACKUP SUPPLY 110/220 VAC, 50/60 Hz NX-308 NX-820 NX-1232 NX-308 NX-820 NX-1232 AC 80 Vrms, 25 Hz 50 WATTS MAX 55

NX-SERIES HYBRID KEY SYSTEM GENERAL DESCRIPTION SECTION 5.5 SYSTEM TONES AND RINGS DIAL TONE : A steady tone that indicates dialing may begin CONTINUOUS RING-BACK TONE : Indicates the station dialed is ringing. 400 ON / 200 OFF/ 400 ON / 3000 OFF BUSY TONE: Indicates the station dialed is busy. 500

NX-SERIES HYBRID KEY SYSTEM GENERAL DESCRIPTION SECTION STATION RING: Indicates an intercom call is ringing on your station. 400 ON / 200 OFF / 400 ON / 3000 OFF DOORPHONE RING: Indicates a doorphone call is ringing on your station. 500 ON / 500 OFF / 500 ON / 500 OFF ALARM RING: Indicates an alarm

INSTALLATION SECTION

NX-SERIES HYBRID KEY SYSTEM INSTALLATION SECTION 4 MDF CABLING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9 4.1 Clip type MDF Cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-19 4.2 Using to Cable tie . . . . . . . . . . . . . . . . . . . . . . .

NX-SERIES HYBRID KEY SYSTEM INSTALLATION SECTION FIGURE 2-1 MOUNTING THE KSU 2.3 AC Power Selection ( See FIGURE 2-2 ) Before pluging in the KSU, set the AC power selection connector. The Power board of each system has three power connectors. One is for 0V (Ground) and the rest are for 110V/220V

NX-SERIES HYBRID KEY SYSTEM INSTALLATION SECTION 3. INSTALLATION EXPANSION CARDS & OPTION BOARDS Unpack and inspect each card before installing. Check for signs of physical damage. If any damage is detected, do not attempt to install. 3.1 NX-2TRK Card ( See FIGURE 3 — 1 ) Insert the NX-2TRK Card

NX-SERIES HYBRID KEY SYSTEM INSTALLATION SECTION 3.8 NX-SMDR/R-MMC Board ( See FIGURE 3 — 7 ) Install the NX-SMDR/R-MMC board on the bottom of the base board. 3.9 NX-DPH/PAGING Board ( See FIGURE 3 — 8 ) Install the NX-DPH/PAGING board on the middle of the base board. FIGURE 3-7 NX-SMDR/R-MMC BOARD

NX-SERIES HYBRID KEY SYSTEM INSTALLATION SECTION 3.13.2 NX-820 SYSTEM ( See FIGURE 3-13) NX-820 system can have up to three expansion cards under the base board. And NX-SMDR/R-MMC, NX-DPH/PAGING, NX-MPD and NX-PRS option boards are installed on the surface of Base board. NX-MPD or NX-PRS Board.

NX-SERIES HYBRID KEY SYSTEM INSTALLATION SECTION 50 PIN CHAMP P1 CONNECTOR PIN NO. 1 26 2 27 3 28 4 29 5 30 6 31 7 32 8 33 9 34 10 35 11 36 12 37 13 38 14 39 15 40 16 41 17 42 18 43 19 44 20 45 21 46 22 47 23 48 24 49 25 50 COLOR BL-W W-BL O-W W-O GN-W W-GN BR-W W-BR S-W W-S BL-R R-BL O-R R-O GR-R

NX-SERIES HYBRID KEY SYSTEM INSTALLATION SECTION 50 PIN CHAMP P1 CONNECTOR PIN NO. 1 26 2 27 3 28 4 29 5 30 6 31 7 32 8 33 9 34 10 35 11 36 12 37 13 38 14 39 15 40 16 41 17 42 18 43 19 44 20 45 21 46 22 47 23 48 24 49 25 50 COLOR MDFB-C BL-W W-BL O-W W-O GN-W W-GN BR-W W-BR S-W W-S BL-R R-BL O-R

NX-SERIES HYBRID KEY SYSTEM INSTALLATION SECTION 50 PIN CHAMP P1 CONNECTOR PIN NO. COLOR 1 26 2 27 3 28 4 29 5 30 6 31 7 32 8 33 9 34 10 35 11 36 12 37 13 38 14 39 15 40 16 41 17 42 18 43 19 44 20 45 21 46 22 47 23 48 24 49 25 50 BL-W W-BL O-W W-O GN-W W-GN BR-W W-BR S-W W-S BL-R R-BL O-R R-O GR-R

NX-SERIES HYBRID KEY SYSTEM INSTALLATION SECTION 50 PIN CHAMP 2 TRK CONNECTOR PIN NO. COLOR 1 26 2 27 3 28 4 29 5 30 6 31 7 32 8 33 9 34 10 35 11 36 12 37 13 38 14 39 15 40 16 41 17 42 18 43 19 44 20 45 21 46 22 47 23 48 24 49 25 50 BL-W W-BL O-W W-O GN-W W-GN BR-W W-BR S-W W-S BL-R R-BL O-R R-O

NX-SERIES HYBRID KEY SYSTEM INSTALLATION SECTION MDF Pin No. Champ Pin No. MDF Pin No. Champ Pin No. 1 26 21 36 2 1 22 11 3 27 23 37 4 2 24 12 5 28 25 38 6 3 26 13 7 29 27 39 8 4 28 14 9 30 29 40 10 5 30 15 11 31 31 41 12 6 32 16 13 32 33 42 14 7 34 17 15 33 35 43 16 8 36 18 17 34 37 44 18 9 38 19

NX-SERIES HYBRID KEY SYSTEM INSTALLATION SECTION 5. CONNECTING TELEPHONE LINES 5.1 SAFETY PRECAUTIONS To limit the risk of personal injury, always follow these precautions before connecting to TELCO circuits: Never install telephone wiring during a lightning storm. Never install telephone jacks in

NX-SERIES HYBRID KEY SYSTEM INSTALLATION SECTION 6.2.1 NX-308 — Related Switch Location (FIGURE 6-3) To connect the single line telephone to the any station from #2 to #8 of basic KSU, the related DIP switches should be set as follows. Station No. STN 2 STN 3 STN 4 STN 5 STN 6 STN 7 STN 8 Releated

NX-SERIES HYBRID KEY SYSTEM INSTALLATION SECTION Music Source Selection shunt pin PFT selection switch Hybrid station selection switches Memory Back-up enable shunt pin Hybrid Station Configuration KTS : SLT : FIGURE 6-3 NX-308 KSU SWITCH LOCATIONS 2 — 24

NX-SERIES HYBRID KEY SYSTEM INSTALLATION SECTION Music Source Selection shunt pin Memory Back-up enable shunt pin Hybrid station selection switches Hybrid Station Configuration KTS : SLT : FIGURE 6-5 NX-1232 KSU SWITCH LOCATIONS 2 — 26

NX-SERIES HYBRID KEY SYSTEM INSTALLATION SECTION 7.3 DOORPHONE AND DOOR LOCK RELEASE (See FIGURE 7-3) System users have the capability of communicating with an optional door phone when the NX-DPH/PAGING board is installed. A maximum of two door phones may be installed per system. To connect the

NX-SERIES HYBRID KEY SYSTEM INSTALLATION SECTION R-MMC (9 PIN) PC (9 PIN) RXD 2 TXD 3 DTR 4 SGND 5 CTS 8 2 RXD 3 TXD 4 DTR 5 SGND NOTE : If the CTS pin is not connected, the system cannot check the printer (MODEM) status (power ON/OFF, paper empty, etc.) FIGURE 7-4 SMDR & REMOTE PROGRAMMING

NX-SERIES HYBRID KEY SYSTEM INSTALLATION SECTION FIGURE 7-5 CONNECTING EXTERNAL BATTERY 8. BEFORE POWER UP During initial installation, it is best to verify proper system operation before plugging in any amphenol-type cables to the MDF. If you have already plugged the cables in, unplug them. Verify

NX-SERIES HYBRID KEY SYSTEM INSTALLATION SECTION 9-3 HOW TO REMOVE THE HANDSET CORD FROM THE HANDSET Driver Insert the sharp-edged one (ex:driver, pincette,…) into the slight gap of handset. Line holder Slightly push the driver, and lift up the line holder from handset. Now, you have removed the

FEATURES SECTION

NX-SERIES HYBRID KEY SYSTEM FEATURES SECTION TABLE OF CONTENTS FEATURES 1. FEATURE DESCRIPTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1 1.1 SYSTEM FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1 1.2 STATION FEATURES . . . . . . . . . . . . . . . . .

NX-SERIES HYBRID KEY SYSTEM FEATURES SECTION NOTICE this manual describes stadard setting. Some features, MMC Codes and default data may be different from those shown depending on the country.

NX-SERIES HYBRID KEY SYSTEM FEATURES SECTION 1. FEATURE DESCRIPTION 1.1 SYSTEM FEATURES LIVE SYSTEM PROGRAMMING ACCOUNT CODE (Voluntary) ALL CALL VOICE PAGE ATTENTION TONE AUTHORIZATION CODES (Voluntary) AUTOMATIC HOLD BACKGROUND MUSIC BATTERY BACKUP (Memory Protection) BATTERY BACKUP (System) CALL

NX-SERIES HYBRID KEY SYSTEM FEATURES SECTION ACCOUNT CODE (Voluntary) Station users may enter an account code of up to seven (7) digits before hanging up a call. This account code will appear in the last column of the SMDR for that call record. Keyset users may enter this code using the ACC button

NX-SERIES HYBRID KEY SYSTEM FEATURES SECTION BATTERY BACKUP (Memory Protection) In the event that power is lost to the system, all customer data contained in memory is backed up by a base board Ni/Cd battery sufficient for at least seven (7) days continuous loss of system power. When power is

NX-SERIES HYBRID KEY SYSTEM FEATURES SECTION CALL HUNT If this feature is enabled on a station, an intercom call while busy will be transferred to another station in the same station group. ➥ MMC 22 CUSTOMER ON/OFF HUNT: ON CALL METERING/PRS You may charge for making outside calls by this feature,

NX-SERIES HYBRID KEY SYSTEM FEATURES SECTION CHAIN DIALING Station users may manually dial additional digits following a Speed-Dial call, or chain together as many Speed-Dial numbers as required. CLASS OF SERVICE System programming may assign any of six outgoing call restriction levels. Refer to

NX-SERIES HYBRID KEY SYSTEM FEATURES SECTION DIRECT TRUNK SELECTION Any station can directly select a specific C.O. line by simply pressing the appropriate button to either originate or answer a call. DIRECTORY NAMES Each station and C.O. line may be assigned a unique directory name. ➥ ➥ MMC 14

NX-SERIES HYBRID KEY SYSTEM FEATURES SECTION EXECUTIVE BARGE-IN (Override) The feature allows specially-programmed stations to override the automatic privacy of another station. Programming provides three options: No Barge-in, With Tone, and Without Tone. When programmed without tone, the

NX-SERIES HYBRID KEY SYSTEM FEATURES SECTION line, trunk group, or Speed-Dial number whenever the station goes off-hook. A hot line delay time of 1 to 9 seconds can be programmed to allow sufficient time to make a different call. ➥ MMC 25 HOT/WARM LINE IN GROUP / OUT OF GROUP Individuals assigned

NX-SERIES HYBRID KEY SYSTEM FEATURES SECTION passcode, and can assign Customer level access to MMCs as needed. CUSTOMER LEVEL This level requires the Customer level passcode and allows access to MMCs assigned by the Technician level in MMC 90. ➥ MMC 90 CUSTOMER USE MMC STATION LEVEL All keysets can

NX-SERIES HYBRID KEY SYSTEM FEATURES SECTION Automatic Night Service Automatic Night Service allows the system to automatically go into and out of Night Service according to system clock time. This feature can be overridden by the Night Service button. ➥ MMC 56 ASSIGN AUTO NIGHT TIME OFF PREMISES

NX-SERIES HYBRID KEY SYSTEM FEATURES SECTION PORT STATUS CHECK Users can view their port status on the LCD. Any one of sixteen (16) status items (IDLE, BUSY, CALLBACK, PROGRAM, etc) may be displayed. ➥ MMC 92 PORT STATUS POWER FAILURE TRANSFER In the event of commercial power loss, the first two

NX-SERIES HYBRID KEY SYSTEM FEATURES SECTION database from a remote location via a customer-provided modem to make programming changes and view traffic reports as a troubleshooting aid. A customer PC can also be connected directly to the Base board for on-site programming. ➥ MMC 80 IO PARAMETER

NX-SERIES HYBRID KEY SYSTEM FEATURES SECTION STATION HUNT GROUPS System programming allows for up to 20 station groups. Four ring patterns are available for each group: SEQUENTIAL, DISTRIBUTE, CONDITION and UNCONDITION. Each group may contain a maximum 8 stations, and a station may be associated

NX-SERIES HYBRID KEY SYSTEM FEATURES SECTION TOLL RESTRICTION There are 250 allow and 250 deny entries of 11 digits each. Each of these entries can apply to dialing classes B, C, D and E. Class A stations have no dialing restrictions and class F stations cannot make outside calls. ➥ ➥ ➥ ➥ MMC 30

NX-SERIES HYBRID KEY SYSTEM FEATURES SECTION at the end of each day or week. The report can also be printed on demand. A customer-provided printer must be connected to the SMDR or R-MMC port in order to print this report. ➥ ➥ MMC 80 IO PARAMETERS MMC 83 CALL TRAFFIC TRANSFER System operation

NX-SERIES HYBRID KEY SYSTEM FEATURES SECTION 1.2 STATION FEATURES ADD-ON MODULE (AOM) APPOINTMENT REMINDER AUTOMATIC HOLD AUTOMATIC PRIVACY BACKGROUND MUSIC BUSY STATION CALLBACK BUSY STATION INDICATION (BLF) DIRECT STATION SELECTION (DSS) DO NOT DISTURB (Programmable) DOOR LOCK RELEASE EXCLUSIVE

NX-SERIES HYBRID KEY SYSTEM FEATURES SECTION AUTOMATIC PRIVACY All conversations on outside lines and intercom calls are automatically private. The privacy feature can be turned off on a per-line basis. BACKGROUND MUSIC While the keyset is on-hook, the HOLD button alternately turns background music

NX-SERIES HYBRID KEY SYSTEM FEATURES SECTION EXECUTIVE / SECRETARY HOT LINES A hands-free communication link is established when the EXECUTIVE/SECRETARY button is pressed. When the EXECUTIVE is in DND mode, all calls are forwarded to the SECRETARY and only the SECRETARY can call the EXECUTIVE. This

NX-SERIES HYBRID KEY SYSTEM FEATURES SECTION LINE QUEUING WITH CALLBACK When the desired outside line is busy, the user can press the CALLBACK key or dial the access code to place his/her station in the queue awaiting that particular line. The user will be called back when the line becomes

NX-SERIES HYBRID KEY SYSTEM FEATURES SECTION the feature key applies to. ➥ MMC 72 STATION KEY PROGRAMMING PROTECTION FROM BARGE-IN Each station can be programmed as either secure or not secure. Secure stations cannot be barged-in on. A not secure station talking to a secure station cannot be

NX-SERIES HYBRID KEY SYSTEM FEATURES SECTION through the speaker. Ring Mode Calls are answered by pressing the SPEAKER button or by lifting the handset. Auto Answer Mode The keyset will automatically answer calls via the speakerphone. Voice Announce Mode Keyset users can hear the caller’s voice,

NX-SERIES HYBRID KEY SYSTEM FEATURES SECTION VACANT STATION MESSAGES Any keyset may select one of twenty messages to be displayed at a calling party’s keyset. Ten messages are fixed, and the remaining ten can be customized by the system administrator (16 character maximum). 01 02 03 04 05 IN A

NX-SERIES HYBRID KEY SYSTEM FEATURES SECTION CALL FOR GROUP IDENTIFICATION When a call is made to a station group, the display will show the called group number. These calls can be answered with a different greeting than calls to the user’s extension number. CALL PROCESSING INFORMATION During

NX-SERIES HYBRID KEY SYSTEM FEATURES SECTION IDENTIFICATION OF RECALLS Hold and Transfer recalls are identified differently. Hold recalls show [HOLD RECALL 203] and Transfer recalls show [RECALL FROM 204]. IDENTIFICATION OF TRANSFERS The display identifies who has transferred a call to the user

NX-SERIES HYBRID KEY SYSTEM FEATURES SECTION 2. FEATURE ID TABLE FEATURE Operator Group Hold Pickup Pickup Page Hold Direct Pickup Hold Call Secretary Call Boss Open Doorphone Call Doorphone Direct Open Doorphone Forced Auto Answer Program Personal Speed-Dial Speed-Dial Saved Number Redial Voice

NX-SERIES HYBRID KEY SYSTEM FEATURES SECTION < Sample SMDR printout > For more detailed SMDR information refer to Page 3-13, STATION MESSAGE DETAIL RECORDING(SMDR). SMDR REPORT FOR [ ] 01/08/96 15:19 ============================================================================ EXT TRK MM:DD STT.TIME

PROGRAMMING SECTION

NX-SERIES HYBRID KEY SYSTEM PROGRAMMING SECTION TABLE OF CONTENTS PROGRAMMING 1. INTRODUCTION TO PROGRAMMING ………………………….. 4-1 1.1 PROGRAMMING OVERVIEW …………………………………………… 4-1 1.2 PROGRAMMING LEVELS

NX-SERIES HYBRID KEY SYSTEM PROGRAMMING SECTION NOTICE this manual describes stadard setting. Some MMC Codes and default data may be different from those shown depending on the country.

NX-SERIES HYBRID KEY SYSTEM PROGRAMMING SECTION 1. INTRODUCTION TO PROGRAMMING 1.1 PROGRAMMING OVERVIEW The system arrives from the factory with default data entered. Connect it to trunks, stations, and power, turn the system on and it is fully operational. The only thing left to do is customize

NX-SERIES HYBRID KEY SYSTEM PROGRAMMING SECTION 1.3 PROGRAM KEYS 1.3.1 NX-keyset with LCD 1X16 LCD Display Programmable Butterns KEYPAD Used to enter data VOLUME (+) or (-) : Used to scroll through stations or trunks. MUTE or MESSAGE : Usually used to select data. TRANSFER : Used to enter the

NX-SERIES HYBRID KEY SYSTEM PROGRAMMING SECTION 1.3.2 Other LCD keysets When the using other types of LCD keysets, such as the AS-30 or 816, programming key assignments will differ from the NX model, as shown in the box below. AS-Keyset NX-keyset 816 keyset TRSF/ALM TRANSFER AUTO RDL N/A SPEED

NX-SERIES HYBRID KEY SYSTEM PROGRAMMING SECTION 2. PROGRAMMING PROCEDURES 2.1 PROGRAM LIST IN NUMERICAL ORDER 00: STATION LOCK 01: CHANGE STATION PASSCODE 45: 46: TRUNK GROUP ASSIGN DISA LINE 10: 11: 12: 13: 14: 15: 16: 17: SET ANSWER MODE CALL FORWARD STATION ON/OFF SET RING FREQUENCY STATION

NX-SERIES HYBRID KEY SYSTEM PROGRAMMING SECTION 2.2 PROGRAM LIST IN ALPHABETICAL ORDER ALARM REMINDER 26 LANGUAGE SELECTION 93 ASSIGN ADD-ON MODULE 37 MAKE/BREAK RATIO 54 ASSIGN AUTO NIGHT TIME 56 OPEN PROGRAMMING 20 ASSIGN BARGE-IN 24 OVERRIDE TABLE 64 ASSIGN BOSS/SECRETARY 36 PAGE ZONE 23 ASSIGN

NX-SERIES HYBRID KEY SYSTEM PROGRAMMING SECTION 2.3 PROGRAM PROCEDURES The following instructions for each MMC assume that you have already opened programming. To open SYSTEM (CUSTOMER) PROGRAMMING: Technician Passcode (default:4321) OR Customer Passcode (default:1234) When finished programming

NX-SERIES HYBRID KEY SYSTEM MMC 00 PROGRAMMING SECTION STATION LOCK Use this MMC to lock or unlock stations in order to control others using your station. UNLOCK LOCKED1 LOCKED2 Normal status Prohibit another user from making outside call. Prohibit another user from dialing or receiving any calls.

NX-SERIES HYBRID KEY SYSTEM MMC 01 PROGRAMMING SECTION CHANGE STATION PASSCODE This MMC is used to reset any keyset’s passcode to its default value of ‘1234’,and cannot display station passcodes. Keyset users can set or change their individual passcodes, which are used to lock or unlock the keyset

NX-SERIES HYBRID KEY SYSTEM MMC 10 PROGRAMMING SECTION SET ANSWER MODE This MMC is used to change the answer mode of any station to one of the following options: 1 RING The keyset will ring. Calls are answered by pressing [SPEAKER], or by lifting the handset. 2 AUTO ANSWER After a short attention

NX-SERIES HYBRID KEY SYSTEM MMC 11 PROGRAMMING SECTION CALL FORWARD This MMC is used to program the call forwarding destination for each station and to set the time for FORWARD NO ANSWER. Each station can forward calls under the following condition. FORWARD ALL FORWARD BUSY FORWARD NO ANSWER NO

NX-SERIES HYBRID KEY SYSTEM MMC 12 PROGRAMMING SECTION STATION ON/OFF This MMC allows the keyset user to set the following features: AUTO HOLD AUTO TIMER HEADSET USE HOT KEYPAD KEY TONE RING PREFERENCE Places an existing C.O. call on hold if another trunk key (C.O. button) is pressed during that

NX-SERIES HYBRID KEY SYSTEM MMC 13 PROGRAMMING SECTION SET RING FREQUENCY This MMC is used to select the ring frequency at each keyset. There are four types of ring frequency available at each keyset. A sample of the selection can be heard when a dial key pad is pressed. PPROCEDURE 1. Press

NX-SERIES HYBRID KEY SYSTEM PROGRAMMING SECTION MMC 14 STATION NAMES This MMC is used to enter a name of up to twelve (12) characters to identify an individual station. Names are entered via the keypad. Each press of a key will select a character. Pressing a different key will advance the cursor to

NX-SERIES HYBRID KEY SYSTEM MMC 15 PROGRAMMING SECTION DATA DISPLAY This MMC is used to change date display mode of each stations. Following date display mode are available. NOTE: AS-30S and SKP-816 model keysets display Western format only. 1 2 3 4 24 12 24 12 WESTERN WESTERN EASTERN EASTERN WED

NX-SERIES HYBRID KEY SYSTEM MMC 16 PROGRAMMING SECTION KEY EXTENDER This MMC is used to view the programmable keys assigned to a keyset station. It also allows the system administrator to assign key extenders to some keys to make a feature key more specific. The feature keys accept extenders are:

NX-SERIES HYBRID KEY SYSTEM MMC 17 PROGRAMMING SECTION STATION SPEED-DIAL This MMC is used to program the personal dial memory assigned to a station. Each station may have up to 20 memory locations, numbered 00 to 19. Each dial number consists of a trunk or trunk group access code followed by a

NX-SERIES HYBRID KEY SYSTEM MMC 20 PROGRAMMING SECTION OPEN PROGRAMMING This MMC is used to open or close Customer or Technician level programming. If programming is not opened and an attempt is made to access a system MMC, the error message [NOT PERMIT] will be displayed. A four-digit Customer

NX-SERIES HYBRID KEY SYSTEM MMC 21 PROGRAMMING SECTION CHANGE PASSCODE Use this MMC to change the passcode allowing access to MMC 20 ‘Open Programming’. NOTE: The passcode is four digits long. A digit may be 0 to 9. The current (old) passcode is required for this MMC. NOTE: Press [HOLD] to reset

NX-SERIES HYBRID KEY SYSTEM PROGRAMMING SECTION MMC 22 CUSTOMER ON/OFF This MMC is used to allow the system administrator to set any of the following keyset features: BGM DND DOOR HUNT MIKE PAGE USE PAGE RECEIVE SMDR When ON, allows the user to hear background music. When ON, allows the user to set

NX-SERIES HYBRID KEY SYSTEM MMC 23 PROGRAMMING SECTION PAGE ZONE This MMC is used to assign a keyset to one (or none) of the four internal paging zones. NOTE: Number 5 is external paging and ‘ ✱ ‘ assigns to all internal and external paging zones. PROCEDURE LCD DISPLAY 1. Press [TRANSFER] and dial

NX-SERIES HYBRID KEY SYSTEM PROGRAMMING SECTION MMC 24 ASSIGN BARGE-IN This MMC is used to set the type of barge-in permitted at a particular station. After the barge-in type is set, the barge-in class can be set. The barge-in class allows or disallows the user to barge-in on another station.

NX-SERIES HYBRID KEY SYSTEM PROGRAMMING SECTION MMC 25 HOT/WARM LINE This MMC is used to assign a hot line/prime line destination to a station. The destination may be any of the following: Station Number Station Group Number Trunk Number Trunk Group Number Speed-Dial location (00 to 99) The Warm

NX-SERIES HYBRID KEY SYSTEM MMC 26 PROGRAMMING SECTION ALARM REMINDER This MMC allows the system administrator or technician to set or change the alarm clock/appointment reminder feature for any station. Three alarms may be set for each station, and each alarm may be defined as a «DAY» alarm or as

NX-SERIES HYBRID KEY SYSTEM MMC 27 PROGRAMMING SECTION VACANT MESSAGE The system provides up to 20 vacant messages that can be selected by any display keyset user. Messages 01 through 10 are pre-programmed, as shown below. Messages 11 through 20 may be customized via this MMC. The selected message

NX-SERIES HYBRID KEY SYSTEM MMC 28 PROGRAMMING SECTION CALL DISC Used to assign the incoming and outgoing call disconnection per station. There are four different option. 0 1 2 3 No Disconnection Out Only In Only Both PROCEDURE LCD DISPLAY 1. Press [TRANSFER] and dial 28 2. Using [VOLUME (-) or

NX-SERIES HYBRID KEY SYSTEM PROGRAMMING SECTION MMC 30 STATION TOLL CLASS This MMC is used to assign any of the 6 different day and/or night class of service to each station, as per the table below: DIAL DIGIT 1 2 3 4 5 6 TOLL CLASS A B C D E F DESCRIPTIONS No restriction Follow allow/deny table

NX-SERIES HYBRID KEY SYSTEM MMC 31 PROGRAMMING SECTION EXT/TRK USE This MMC is used to allow trunks the ability to answer incoming calls, to dial out, or to do both, on a per-station basis. Those abilities are displayed as Y or N for each action (e.g. NY: disallow dialing out and allow answering

NX-SERIES HYBRID KEY SYSTEM MMC 32 PROGRAMMING SECTION INTERCOM USE This MMC is used to allow/disallow station intercom calls. PROCEDURE 1. Press [TRANSFER] and dial 32 2. Use [VOLUME (-) or (+)], to select a station (e.g. 202) To select all stations, press [VOLUME (-)] first 3. Press [REDIAL] or

NX-SERIES HYBRID KEY SYSTEM MMC 33 PROGRAMMING SECTION ASSIGN DOOR RING This MMC is used to designate which devices (station or station group) will ring when a door box button is pressed. PROCEDURE LCD DISPLAY 1. Press [TRANSFER] and dial 33 Display shows designated stations or station groups for

NX-SERIES HYBRID KEY SYSTEM MMC 34 PROGRAMMING SECTION ASSIGN PICKUP GROUP This MMC is used to allow the assignment of stations to call pickup groups. There may be a maximum 10 pickup groups (0~9). An unlimited number of members can belong to each group. Stations can be in only one pickup group at

NX-SERIES HYBRID KEY SYSTEM MMC 35 PROGRAMMING SECTION ASSIGN STATION GROUP This MMC is used to assign members of a station group. There are several options that can be selected for ringing, overflow, group transfer and overflow destination, and group type. There may be a maximum twenty (20)

NX-SERIES HYBRID KEY SYSTEM PROGRAMMING SECTION MMC 35 4d. To assign the overflow port, enter the station or station group number. 4e. Press [MUTE] or [MESSAGE] to select the station group type OR Using KEYPAD, 1 for NORMAL GROUP 2 for VMAA GROUP 4f. To assign amember to the station group, enter

NX-SERIES HYBRID KEY SYSTEM MMC 36 PROGRAMMING SECTION ASSIGN BOSS/SECRETARY This MMC is used to assign BOSS keysets to SECRETARY keysets. One SECRETARY station may include two (2) BOSS stations. PROCEDURE LCD DISPLAY 1. Press [TRANSFER] and dial 36 2. Using [VOLUME (-) or (+)], select the

NX-SERIES HYBRID KEY SYSTEM MMC 37 PROGRAMMING SECTION ASSIGN ADD-ON MODULE This MMC is used to assign an add-on module (AOM) to a station. PROCEDURE 1. Press [TRANSFER] and dial 37 Display shows the first AOM port If there is no AOM port, display shows: 2. Press [VOLUME (-) or (+)], to select the

NX-SERIES HYBRID KEY SYSTEM MMC 38 PROGRAMMING SECTION SLT DIALING TYPE This MMC is used to define the dial type of phone connected to each SLT port. Keysets are not affected by this MMC. There are two dialing types: DIALING TYPES 1 2 DTMF PULSE Dual Tone Multi-Frequency (Touch Tone) Dial Pulse

NX-SERIES HYBRID KEY SYSTEM MMC 39 PROGRAMMING SECTION DATA LINE Used to assign SLT ports to be used for data transmission. VOICE DATA — The station will be used for voice communication. All intrusion and warning tones will be heard during conversation. — The station will be used for data

NX-SERIES HYBRID KEY SYSTEM MMC 40 PROGRAMMING SECTION C.O./PBX LINE This MMC is used to select the mode of the C.O. line. If the PBX mode is chosen, the PBX access code can be recognized allowing more complete toll restrictions. This mode is assigned on a per-trunk basis. PROCEDURE 1. Press

NX-SERIES HYBRID KEY SYSTEM MMC 41 PROGRAMMING SECTION TRUNK DIALING TYPE This MMC is used to set the dial type of each C.O. line. There are two options: DTMF : Dual Tone Multi Frequency (Touch Tone) PULSE : Pulse dial (rotary). PROCEDURE 1. Press [TRANSFER] and dial 41 2. Using [VOLUME (-) or

NX-SERIES HYBRID KEY SYSTEM PROGRAMMING SECTION MMC 42 TRUNK ON/OFF This MMC is used to assign trunk options on a per-trunk basis. OPTION 1A2 EMULATION TRUNK FORWARD RING OVER PAGE TOLL CHECK FREE VOICE MSG TRK DISC DESCRIPTION Trunk override call Allow trunk to be forwarded Allow ring over

NX-SERIES HYBRID KEY SYSTEM MMC 43 PROGRAMMING SECTION ASSIGN TRUNK RING A trunk may have a maximum 16 members(station or station group) assigned to ring. PROCEDURE LCD DISPLAY 1. Press [TRANSFER] and dial 43 2. Using [VOLUME (-) or (+)], select the trunk you want (e.g., 703) 3. Press [REDIAL] or

NX-SERIES HYBRID KEY SYSTEM PROGRAMMING SECTION MMC 44 TRUNK NAMES This MMC is used to assign a name of up to twelve (12) characters to identify a particular trunk. Names are written using the keypad. Each press of a key will select a character. Pressing a different key moves the cursor to the next

NX-SERIES HYBRID KEY SYSTEM MMC 45 PROGRAMMING SECTION TRUNK GROUP This MMC is used to set the free trunk selection type to a specific trunk, trunk group, or to several trunk groups. There are eleven (11) trunk groups: 9 and 80 through 89, and three types of selecting a free trunk line in the

NX-SERIES HYBRID KEY SYSTEM PROGRAMMING SECTION MMC 46 ASSIGN DISA LINE This MMC is used to allow the system the ability to have Direct Inward System Access (DISA). There are four 4 DISA. If a trunk is set to DISA, the voice announcement feature may be used when the VOICE MSG option is enabled in

NX-SERIES HYBRID KEY SYSTEM MMC 50 PROGRAMMING SECTION SYSTEM TIMERS This MMC is used to adjust individual timers as necessary. All available timers are described in the TABLE OF TIMERS AND VALUES. NOTE: Seconds are shown as ‘SEC’, milliseconds as ‘MS’, and minutes as ‘MIN’. PROCEDURE LCD DISPLAY

NX-SERIES HYBRID KEY SYSTEM PROGRAMMING SECTION MMC 50 DISPLAY DOR R OFF (Door Ring OFF time) FIRST DGT (First Digit wait time) HOOK OFF (Hook OFF time) DESCRIPTION controls the duration of ringing at the door ring destination before canceling DEFAULT RANGE 030SEC 1~250SEC controls how long the

NX-SERIES HYBRID KEY SYSTEM MMC 51 PROGRAMMING SECTION TONE/RING CADENCE This MMC is used to customize the tone cadence on a system-wide basis to any one of the eight available selections. Call Technical Support before changing any cadences, as some systems may require default settings. PROCEDURE

NX-SERIES HYBRID KEY SYSTEM MMC 52 PROGRAMMING SECTION SYSTEM WIDE COUNTER This MMC is used to set the values of the system counters. The counters and descriptions are listed below: OPTIONS DESCRIPTION ALM COUNTER (ALARM REMINDER COUNTER) This is the number of times (1 to 99) that an alarm reminder

NX-SERIES HYBRID KEY SYSTEM MMC 53 PROGRAMMING SECTION TRUNK WIDE TIMER This MMC is used to changed trunk timer values. It is not advisable to change these values, with exception of trunk flash time, without assistance from Technical Support. The available options are and listed below: DISPLAY

NX-SERIES HYBRID KEY SYSTEM PROGRAMMING SECTION MMC 54 MAKE/BREAK RATIO This MMC is used to allow the ability to change the duration of the make/break time of pulse (rotary) dial trunks. PROCEDURE LCD DISPLAY 1. Press [TRANSFER] and dial 54 2. Enter the MAKE/BREAK ratio on the KEYPAD (e.g. MAKE:40

NX-SERIES HYBRID KEY SYSTEM MMC 56 PROGRAMMING SECTION ASSIGN AUTO NIGHT TIME This MMC is used to automatically place the system in Night mode. A Night key is not needed, as the system switches automatically, but it is helpful to have a dedicated button so the status can be changed manually. ‘D’ in

NX-SERIES HYBRID KEY SYSTEM PROGRAMMING SECTION MMC 57 CALL COST This MMC is used to program the unit cost of the metering pulse generated by the Central Office. If the MPD card is installed, it will detect the metering pulse provided by Central Exchange and determine the call cost by the number of

NX-SERIES HYBRID KEY SYSTEM MMC 61 PROGRAMMING SECTION TOLL ALLOW TABLE/APPLY This MMC enables you to define which leading digit(s) in a dialing plan are to be allowed and which class(es) should be applied in this allow table. Each entry can define up to 11 digits. PROCEDURE LCD DISPLAY 1. Press

NX-SERIES HYBRID KEY SYSTEM MMC 63 PROGRAMMING SECTION AUTHORIZATION TABLE This MMC is used to list all allowable authorization codes. An authorization code must be four digits long. There are 50 codes allowed in this table. Duplications or number conflicts are not permitted. Each authorization

NX-SERIES HYBRID KEY SYSTEM MMC 64 PROGRAMMING SECTION OVERRIDE TABLE This MMC is used to enter up to five exceptions to toll restriction. These exceptions can be accessed by any class in both Day and Night modes, and are useful to allow access to emergency numbers. Caution should be used regarding

NX-SERIES HYBRID KEY SYSTEM PROGRAMMING SECTION MMC 65 ASSIGN WILD CHARACTER Provides flexibility to toll restriction when a specific numbering plan is desired. There are only three entry tables, but more than one digit can be assigned per table if necessary. PROCEDURE LCD DISPLAY 1. Press

NX-SERIES HYBRID KEY SYSTEM MMC 66 PROGRAMMING SECTION SYSTEM SPD-DIAL TOLL RESTRICTION Enables you to define whether the system allows or denies long distance numbers in system Speed-Dialing to override toll restriction. BYPASS TOLL Any station can use system speed dial numbers without

NX-SERIES HYBRID KEY SYSTEM MMC 67 PROGRAMMING SECTION ASSIGN SYSTEM SPEED-DIAL This MMC is used to store up to eighty (80) system Speed-Dial numbers. The system Speed-Dial number is composed of 2 digits (20 to 99) and a maximum 30-digit telephone number can be stored at each Speed-Dial number.

NX-SERIES HYBRID KEY SYSTEM MMC 70 PROGRAMMING SECTION DIAL NUMBERING PLAN This MMC provides the access codes and dialing plan needed for operation of features and programs. The system comes with a wide range of acceptable numbering plans set as default, and the option to customize the dialing

NX-SERIES HYBRID KEY SYSTEM PROGRAMMING SECTION MMC 70 DPC EXC FAT FLS FWA FWB FWC FWN GPC GPS HED HLD IOG LNR MPG MSA MSC MSL OPR PAG REC SDI SGR SNR SPD STN TRK TGR UPC VAC : 10 : 12 : 14 : 49 : 61 : 62 : 60 : 63 : 66 :✱ : 69 : 11 : 53 : 19 : 56 : 43 : 42 : 41 :0 : 55 : 18 : 15 : 500-519 : 17 :

NX-SERIES HYBRID KEY SYSTEM MMC 71 PROGRAMMING SECTION SYSTEM KEY PROGRAMMING This MMC allows for the customizing of programmable keys system-wide. PROCEDURE LCD DISPLAY 1. Press [TRANSFER] and dial 71 2. Using [VOLUME (-) or (+)], select the type of keyset There are 7 keyset types: NX 24, NX 12,

NX-SERIES HYBRID KEY SYSTEM PROGRAMMING SECTION MMC 71 SKP-816 09: 201 10: 202 11: 203 12: 204 13: 205 14: 206 15: 207 16: 208 17: 209 18: 210 19: 211 20: 212 21: 213 22: 214 23: 215 24: 216 NX-AOM 01: NONE 02: NONE 03: NONE 04: NONE 05: NONE 06: NONE 07: NONE 08: NONE 09: NONE 10: NONE 11: NONE

NX-SERIES HYBRID KEY SYSTEM MMC 72 PROGRAMMING SECTION STATION KEY PROGRAMMING This program allows customizing programmable keys on specific electonic keysets on the system. The program also provides a tool for duplicating data to other keysets to have the same key format structure. Copy source and

NX-SERIES HYBRID KEY SYSTEM PROGRAMMING SECTION MMC 73 KEY TEST This program allows you to check whether each key works properly. PROCEDURE 1. Press [TRANSFER] and dial 73 All LEDs light and station rings. Display sets show the full matrix pattern for 16 characters. All tri-color LEDs light amber

NX-SERIES HYBRID KEY SYSTEM PROGRAMMING SECTION MMC 80 SYSTEM I/O PARAMETERS This MMC provides a means of setting parameters for the serial I/O ports to work with SMDR and Remote MMC. Programming is accomplished easily with the tables below to customize either I/O port. PARAMETER TYPE OF SERVICE

NX-SERIES HYBRID KEY SYSTEM PROGRAMMING SECTION MMC 81 SMDR OPTIONS This MMC allows the system administrator to select information to be printed on the SMDR report. OPTIONS DESCRIPTIONS PAGE HEADER This option determines whether a page header will print at the top of each page. Normally turned off

NX-SERIES HYBRID KEY SYSTEM MMC 83 PROGRAMMING SECTION CALL TRAFFIC REPORT This MMC is used to print a traffic report and select options. Four types of printing are available, each with has two options. These are listed below: NO. 0 1 2 3 TYPE NO NOW DAILY WEEKLY DESCRIPTION No print Printed on

NX-SERIES HYBRID KEY SYSTEM MMC 90 PROGRAMMING SECTION CUSTOMER USE MMC Allows the station user access to certain MMCs. For example, it is advised that the user have access to MMC11 Call Forward, but not MMC60 Toll Deny. PROCEDURE LCD DISPLAY 1. Press [TRANSFER] and dial 90. 2. Press [VOLUME (-) or

NX-SERIES HYBRID KEY SYSTEM MMC 91 PROGRAMMING SECTION SYSTEM VERSION This MMC provides display of the current software version of the KSU and the KEYSET, and the date the product was made. This is a READ ONLY MMC. PROCEDURE LCD DISPLAY 1. Press [TRANSFER] and dial 91 2. Press [VOLUME (-) or (+)]

NX-SERIES HYBRID KEY SYSTEM MMC 93 PROGRAMMING SECTION LANGUAGE SELECTION Used to select one of three (3) languages to display in keyset LCDs. Choose an entry number from the table below: ENTRY NUMBER 1 2 3 LANGUAGE ENGLISH SPANISH PORTUGUESE NOTE : English is displayed while in MMC mode. PROCEDURE

NX-SERIES HYBRID KEY SYSTEM MMC 94 PROGRAMMING SECTION HALT PROCESS Use only in the event that all data processing must be stopped. The four-digit Technician Passcode is required to access this MMC. This MMC will not interfere with any call in progress, but attempting a new call will result in a

NX-SERIES HYBRID KEY SYSTEM MMC 95 PROGRAMMING SECTION SYSTEM RESTART Provides two methods of restarting the system. OPTIONS DESCRIPTION RESET SYSTEM CLEAR MEMORY Restart the system only. Restart the system and clear all memory and set all functions to their default values. Extreme care should be

NX-SERIES HYBRID KEY SYSTEM PROGRAMMING SECTION

APPENDIX SECTION A. REMOTE PROGRAMMING B. DATABASE DOWNLOAD C. DISA VOICE ANNOUNCEMENT

NX-SERIES HYBRID KEY SYSTEM APPENDIX A APPENDIX A REMOTE PROGRAMMING REMOTE PROGRAMMING Remote programming capability has been incorporated in the NX-SERIES via the R-MMC serial port on the SMDR/R-MMC board option mounted on the base unit. This port is configured as a programming port only. The

NX-SERIES HYBRID KEY SYSTEM APPENDIX A REMOTE PROGRAMMING 1.3 BEGIN PROGRAMMING Dial the customer modem number and establish a communication link with the customer site. Once communication is established, press the TAB key on the PC keyboard to receive the NX-SERIES system header display (below).

NX-SERIES HYBRID KEY SYSTEM APPENDIX A REMOTE PROGRAMMING 2. ON-SITE PROGRAMMING VIA PC TERMINAL On-site programming via a PC terminal has been incorporated in the NX-SERIES via serial communication port R-MMC of the SMDR/R-MMC board mounted on the Base board. This port is configured as a

NX-SERIES HYBRID KEY SYSTEM APPENDIX A REMOTE PROGRAMMING open programming and begin the on-site programming session. NOTE: The header will display CUSTOMER and the name assigned in MMC 81. 2.3 PROGRAMMING PROTOCOL The NX-SERIES will only recognize keystrokes on the PC keyboard that have been

NX-SERIES HYBRID KEY SYSTEM APPENDIX B APPENDIX B DATABASE DOWNLOAD DATABASE DOWNLOAD 1. Introduction To Database Download Programming A database download programming capability has been incorporated into the NXSERIES via the communication (serial) SMDR port of the optional SMDR/R-MMC card mounted

NX-SERIES HYBRID KEY SYSTEM APPENDIX B DATABASE DOWNLOAD 3) Enter the DATABASE DOWNLOAD directory. 4) Double-click on the icon that was created by the install program in the Windows -«NX_DOWN» 5) You will see Windows shown below. Figure 1.1 Main Window 3. 2 Setup Of Database Downloading Program

NX-SERIES HYBRID KEY SYSTEM APPENDIX B DATABASE DOWNLOAD 6) Choose Download / Serial Port*** 7) Check COM port in the Select serial port check box Select OK button. Figure 1.3 Port dialog box 4. Using database downloading program 4.1 Downloading 1) Choose DOWNLOAD / Download to File***. 2) Input

NX-SERIES HYBRID KEY SYSTEM APPENDIX B DATABASE DOWNLOAD Figure 1.6 MMC page tab 4.3 Save file This option saves the downloaded file with another name with the save file option. 4.4 Print file This option prints the database file that you downloaded 4.5 Help This option shows the program version

NX-SERIES HYBRID KEY SYSTEM APPENDIX C APPENDIX C DISA VOICE ANOUNCEMENT DISA VOICE ANOUNCEMENT 1. DISA AUTOMATIC ANSWER The system answers automatically an incoming DISA (Direct Inward System Access) call and sends the message: «This is XXX company. Extension number, please». This facilitates

NX-SERIES HYBRID KEY SYSTEM APPENDIX C DISA VOICE ANOUNCEMENT Start to record through handset or speaker phone. After recording, you can hear automatically the recorded message. NOTE In case of first Power on, record phrase 1 to phrase 4 in sequence. 3.3 Monitoring Dial ’18’ and the customer

BACK-UP DATA SHEETS

NX- _____________ SYSTEM DATABASE FORMS CUSTOMER NAME : ADDRESS : TELEPHONE NUMBER : DATABASE CONTAINS _____________SHEETS

SYSTEM CONFIGURATION SYSTEM EXPANSION Bd. STATION DATA STATION LOCK ANSWER NO. (00) MODE (10) STATION ON / OFF (12) AUTO AUTO HOLD TIMER COPY AS NEEDED HEADSET HOT USE KEY KEYPAD TONE RING FREQ. NAME TOLL (14) CLASS (30) SHEET _____ OF_______

MMC 11 CALL FORWARD STATION NO. FORWARD ALL MMC 17 STATION SPEED-DIAL DESTINATION FORWARD BUSY STATION NO. ENTRY NO. MMC 21 FORWARD NO ANSWER NO ANSWER TIME SPEED-DIAL NO. CHANGE PASSCODE PASSCODE MMC 22 STATION NO. MMC 23 CUSTOMER ON/OFF BGM DND DOOR HUNT MIKE PAGE USE PAGE RECEIVE SMDR PAGE ZONE

MMC 24 OPTION BARGE-IN : STATION NO. MMC 25 BARGE-IN CLASS HOT / WARM LINE STATION NO. MMC 26 DESTINATION ALARM REMINDER STATION NO. MMC 27 ALARM NO. ALARM TIME DAY/DALY VACANT MESSAGE MESSAGE NO. MMC 31 WARM LINE DELAY TIME MESSAGE TRUNK USE STATION NO. COPY AS NEEDED TRUNK NO. DIAL ANSWER SHEET

MMC 32 INTERCOM USE STATION NO. MMC 33 DESTINATION STATION ASSIGN DOOR RING DOOR NO. MMC 34 USE DAY NIGHT PICKUP GROUP GROUP NO. MEMBER ID STATION NO. PICKUP GROUP NO. : MAXIMUM NUMBER OF PICKUP GROUPS IS 10. MMC 35 STATION GROUP STATION GROUP NO. : RING OVEFLOW TIME TRSF. TIME OVERFLOW PORT TYPE

MMC 37 AOM ADD-ON MODULE MASTER MMC 38 AOM MASTER AOM MASTER SLT DIALING TYPE STATION NO. MMC 39 TYPE STATION NO. TYPE STATION NO. VOICE / DATA TRUNK NO. CO/PBX DATA LINE STATION NO. MMC 40 VOICE / DATA C.O. PBX LINE TRUNK NO. CO/PBX TRUNK LINE DATA TRUNK NO. DIAL TYPE (41) COPY AS NEEDED TRUNK ON

MMC 45 MODE TRUNK GROUP : GROUP NO. : MEMBER : MAXIMUM NUMBER OF TRUNK GROUPS IS 11. MMC 46 ASSIGN DISA LINE TRUNK NO. MMC 50 DISA OPTION VOICE MSG (42) SYSTEM TIMERS TIMER RANGE DEFAULT ALM R INT 1~250 sec 025 sec ALM R DUR 1~250 sec 010 sec ARDL INT 1~250 sec 045 sec ARDL REAL 1~250 sec 045 sec

SMDR PULAS 1~250 sec 030 sec SMDR DRMF 0~250 sec 015 sec TRK DISC 1~250 min 030 min MMC 51 TONE / RING CADENCE TONE/RING ON MMC 52 OFF ON SYSTEM WIDE COUNTER OPTION COUNTER MMC 53 TRUNK WIDE TIMER TIMER RANGE DEFAULT CLEARING 1~25 sec 00 sec CO SUPV 100~2500 ms 0000 ms F DGT DLY 100~2500 ms 1000 ms

MMC 57 CALL COST UNIT COST : MMC 60 TOLL DENY TABLE / APPLY ENTRY APPLY B MMC 61 C ENTRY D E APPLY B C D E TOLL ALLOW TABLE / APPLY ENTRY APPLY B C ENTRY D MMC 62 PBX ACCESS CODE PBX NO. CODE COPY AS NEEDED E APPLY B PBX NO. C D E CODE SHEET _____ OF_______

MMC 63 NO. AUTHORIZATION CODE CODE MMC 64 NO. CLASS NO. CLASS CODE NO. CODE WILD CHARACTER X : Y : Z : MMC 67 ASSIGN SYSTEM SPEED-DIAL NO. SPEED DIAL NO. MMC 70 DIAL NUMBERING PLAN ENTRY CODE OVERRIDE TABLE CODE MMC 65 NO. ACCESS CODE ENTRY NO. ACCESS CODE SPEED-DIAL NO. ENTRY ACCESS CODE MMC 71 /

AS-30 01: 07: 13: 19: 25: SKP-816 09: 10: 11: 12: 13: 14: 15: 16: 02: 08: 14: 20: 26: 03: 09: 15: 21: 27: 17: 18: 19: 20: 21: 22: 23: 24: 01: 05: NX-AOM 01: 02: 03: 04: 05: 06: 07: 08: 09: 10: 11: 12: 13: 14: 15: 16: 17: 18: 19: 20: 21: 22: 23: 24: MMC 80 IO PARAMETERS COM1 COM2 XON OFF COM1 MMC 81

CODE: GA68-60655A Edition : 05 DN April 1999 Printed In Korea